1 / 6 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l52d6 high gain, low noise amplifier 1) oip3 is measured with two tones at an output power of +4 dbm/tone separated by 1mhz. *100% in - house dc & rf testing is done on packaged products before taping * please find the max. input power data from http://www.asb.co.kr/pdf/maximum_input_power_analysis.pdf parameters units typical testing frequency mhz 900 1950 gain db 24 21 s11 db - 18 - 18 s22 db - 10 - 10 output ip3 1) dbm 33 33 noise figure db 0.55 0.65 output p1db dbm 19 18 current ma 50 50 device voltage v 5 5 parameters units min typ max frequency mhz 1950 gain db 21 s11 db - 18 s22 db - 10 output ip3 dbm 33 noise figure db 0.65 output p1db dbm 18 cu rrent ma 50 device voltage v 5 parameters rating operating case temperature - 40 to + 85 c storage temperature - 40 to + 150 c device voltage +6 v operating junct ion temper a ture + 150 c input rf power ( cw, 50ohm matched)* 22 dbm feature s description package style: dfn - 6 21 db gain at 1950 mhz 33 dbm oip 3 at 1950 mhz 18 dbm p1db at 1950 mhz 0.65 db nf at 1950 mhz s11 < - 18 db mttf > 100 years single supply ASL52D6 is an easy - to - use low noise, high gain, and high linearity over a wide range of frequency up to 5 ghz. it is also suitable for use in the low noise amplifier block of the mobile wireless systems of pcs, wcdma, wibro, wimax, and wlan so on. . it has an active bias network for stable current over te m perature and process variation. the amplifier is available in a dfn - 6 package and pa sses the stringent dc, rf, and reliability tests. a p plications gps receiver cdma, gsm, w - cdma, pcs wibro, wimax, wlan gain block if amplifier product specifications* more inform a tion tel: (82) 42 - 528 - 7 22 3 f ax : (82) 42 - 528 - 72 22 asb inc. , 4 th fi. venture town bldg. , 367 - 17 goijeong - d ong, seo - gu, d aejon 30 2 - 716, korea typical perfor m ance a p plication circuit 900 mhz gps 1500 - 1600 mhz 1950 mhz tetra 360 - 450 mhz absolute maximum ratings pin configuration pin no. function 1 bias 2 rf in 5 rf out 3, 4, 6 nc/ gnd backside paddle gnd
2 / 6 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l52d6 high gain, low noise amplifier outline drawing note : 1. backside metal paddle is rf and dc ground. pin no. function pin no. function. 1 bias 4 gnd or nc 2 rf in 5 rf out 3 gnd or nc 6 gnd or nc esd classification & moisture sensitivity level symbols dimensions (in mm) min nom max a 0.80 0.85 0.90 a1 0 0.010 0.030 a3 --- 0.20ref --- b 0.35 0.40 0.45 d 2.95 3.00 3.03 d1 --- 2.25bsc --- e 1.95 2.00 2.03 e1 --- 0.65bsc --- e --- 0.95bsc --- l 0.275 0.325 0.375 q - 12 --- 0 as l52d6 part no. esd classification hbm class 1a voltage level: 400 v mm class a voltage level: 50 v caution: esd - sensitive device! moisture sensitivity level (msl) level 3 at 260 c reflow
3 / 6 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l52d6 high gain, low noise amplifier 0 300 600 900 1200 1500 1800 2100 0 5 10 15 20 25 30 gain (db) frequency (mhz) 0 300 600 900 1200 1500 1800 2100 -30 -25 -20 -15 -10 -5 0 5 s11 (db) frequency (mhz) 0 300 600 900 1200 1500 1800 2100 -30 -25 -20 -15 -10 -5 0 5 s22 (db) frequency (mhz) 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 0 1 2 3 4 5 6 7 8 9 10 stability factor frequency (mhz) rf out c1=100 pf c3=100 pf c5=100 pf c6=1 m f l2=33 nh vs=5 v l3=8.2 nh ASL52D6 l1=39 nh c1=100 pf l2=6.8 nh c7=100 p f r1=5.1 k w 1) oip3 is measured with two tones at an output power of +4 dbm/tone separated by 1mhz. board layout ( fr4, 25x25 mm 2 , 0.8t) schematic s - parameters & k - factor parameter symbol te st conditions min. typ. max. unit power gain g p f = 900 mhz 24 db noise figure nf f = 900 mhz 0.55 db input return loss rl in f = 900 mhz - 18 db output return loss rl out f = 900 mhz - 10 db 1 db gain compression output power p o(1db) f = 900 mh z 19 dbm 3 rd intercept point output power 1) oip3 f = 900 mhz 33 dbm circuit current i cc f = 900 mhz non - rf 50 ma application circuit 900 mhz +5 v
4 / 6 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l52d6 high gain, low noise amplifier rf in rf out c1=100 pf c3=100 pf c5=100 pf c6=1 m f l2=12 nh vs=5 v l1=4.7 nh ASL52D6 l1=12 nh c1=100 pf l2=8.2 nh 1300 1400 1500 1600 1700 1800 0 5 10 15 20 25 30 gain (db) frequency (mhz) 1300 1400 1500 1600 1700 1800 -30 -25 -20 -15 -10 -5 0 s11 (db) frequency (mhz) 1300 1400 1500 1600 1700 1800 -40 -35 -30 -25 -20 -15 -10 -5 0 s22 (db) frequency (mhz) 0 500 1000 1500 2000 2500 3000 0 1 2 3 4 5 6 7 8 9 10 stability factor frequency [mhz] 1) oip3 is measured with two tones at an output power o f +4 dbm/tone separated by 1mhz. board layout ( fr4, 25x25 mm 2 , 0.8t) schematic s - parameters & k - factor parameter symbol unit frequency (mhz) 1500 1600 power gain g p db 24.5 23.7 noise figure nf db 0.5 5 0.55 input return loss rl in db - 18 - 18 output return loss rl out db - 18 - 17 1 db gain compression output power p o(1db) dbm 15 14.5 3 rd intercept point output power 1) oip3 dbm 33 33 circuit current i cc ma 50 50 application circuit 1500 - 1600 mhz +5 v
5 / 6 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l52d6 high gain, low noise amplifier 1400 1600 1800 2000 2200 2400 2600 0 5 10 15 20 25 gain (db) frequency (mhz) 1400 1600 1800 2000 2200 2400 2600 -30 -25 -20 -15 -10 -5 0 5 s11 (db) frequency (mhz) 1400 1600 1800 2000 2200 2400 2600 -30 -25 -20 -15 -10 -5 0 5 s22 (db) frequency (mhz) 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 0 1 2 3 4 5 6 7 8 9 10 stability factor frequency (mhz) rf in rf out c1=100 pf c3=100 pf c5=100 pf c6=1 m f l3=10 nh vs=5 v l1=2.7 nh ASL52D6 l2=8.2 nh c1=100 pf l3=3.9 nh 1) oip3 is measured with two tones at an output power of +4 dbm/tone separated by 1mhz. board layout ( fr4, 25x25 mm 2 , 0.8t) schematic s - parameters & k - factor parameter symbol test conditions min. typ. max. unit power gain g p f = 1950 mhz 21 db noise figure nf f = 1950 mhz 0.65 db input return loss rl in f = 1950 mhz - 18 db output return loss rl out f = 1950 mhz - 10 db 1 db gain compression output power p o(1db) f = 1950 mhz 18 dbm 3 rd intercept point output power 1) oip3 f = 1950 mhz 33 dbm circuit current i cc f = 1950 mhz non - rf 50 ma a pplication circuit 1950 mhz +5 v
6 / 6 asb inc. sales@asb .co.kr tel: +82 - 42 - 528 - 7223 may 2012 as l52d6 high gain, low noise amplifier rf in rf out c1=100 pf c3=100 pf c5=100 pf c6=1 m f l2=33 nh vs=5 v l3=8.2 nh ASL52D6 l1=100 nh c1=100 pf l2=6.8 nh c7=100 p f r1=820 w 0 250 500 750 1000 0 5 10 15 20 25 gain (db) frequency (mhz) 0 250 500 750 1000 -30 -25 -20 -15 -10 -5 0 s11 (db) frequency (mhz) 0 250 500 750 1000 -25 -20 -15 -10 -5 0 s22 (db) frequency (mhz) 0 500 1000 1500 2000 2500 3000 0 1 2 3 4 5 6 7 8 9 10 stability factor frequency [mhz] 1) oip3 is measured with two tones at an output power of +4 dbm/tone separated by 1mhz. schematic s - parameters & k - factor application circuit t e tra 360 ~ 450 +5 v parameter symbol unit frequency (mhz) 360 450 power gain g p db 21.3 21.1 noise figure nf db 0.9 0.9 input return loss rl in d b - 18 - 18 output return loss rl out db - 18 - 18 1 db gain compression output power p o(1db) dbm 19 19 3 rd intercept point output power 1) oip3 dbm 32 32 circuit current i cc ma 5 0 5 0 board layout ( fr4, 25x 25 mm 2 , 0.8t)
|
